ASICs and FPGAs are the trendy manner of mining cryptocurrency. Latest fashions just like the BlackMiner F1 (check profits), Imperivm V2 (check profits) and the Innosilicon A10 ETH grasp (check profits) can look fairly tempting (particularly if in case you have low-cost electrical energy) and a few of you might be in all probability contemplate getting your self one or two models – in any case, you purchase a kind of unhealthy boys, plug them in and the earnings begins flowing into your pockets. No headache, no points.
The issue? These of you who noticed an ASIC or FPGA board in motion know the way noisy these issues are. Mining is meant to be one thing everybody can do at house, nonetheless in actuality you don’t wish to have that factor anyplace near your residing area.
Through the years individuals got here up with totally different options to this problem – selfmade immersion tanks, water cooling, and so forth. I used to search for my methods round it, too. From my private expertise, water/oil cooling is sweet however silencer containers are the way in which to go for a number of causes:
- Ease of Set up – Open the silencer field, put the miner in, shut the lid and also you’re able to go.
- Re-Usability – The miner leaves the field in the identical state it entered it. You don’t have to wash the mineral oil off within the case you wish to use the miner elsewhere.
- Low Upkeep – Something that includes liquid cooling requires a pump and pumps are often essentially the most weak half that breaks essentially the most usually.
- Decrease Value – immersion tanks are costlier (pumps aren’t low-cost), plus they require you to purchase a number of gallons of mineral oil, which isn’t low-cost both.
Moreover, even with water cooling, the immersion field will nonetheless have followers that might be preserving the liquid cool. You continue to gotta clear these infrequently, and so they nonetheless produce noise.
Silencer Bins are the Option to Go
From the standpoint of a house miner, I spotted that silencer containers are essentially the most affordable resolution which have the very best stability between value, ease of use and outcomes. Silencer containers would possibly supply much less cooling and noise discount than immersion tanks, nonetheless what they supply is nice sufficient to make mining at house potential.
Which Bins to Use?
The obvious resolution that got here to my thoughts was to make my very own silencer containers. In any case, the design is fairly simple and simple to repeat. Or that’s what I believed. After fiddling in my workshop for a number of weeks I spotted that this isn’t simple because it appears. I would like factory-grade gear and high quality supplies to make a field that has obtained the effectivity I’m in search of.
After giving up on DIY containers, I discovered a supplier, a manufacturing unit that may produce such silencer containers and I instantly fell in love with them. A number of of my fellow miners and I are able to order a batch of these containers for our ASICs and FPGAs. Let me introduce to you the:
The Miner Silencer Field offers noise insulation for one normal-sized ASIC or FPGA unit at a time. It has built-in followers and electronics. Whereas it doesn’t supply 100% silence, it makes the FPGA / ASIC fairly quiet. You may then put it in your workplace and it gained’t blow everybody’s ears out. The field additionally cuts off the high-end a part of the sound, making the sound similar to that of a desktop laptop.
That is the professional #1. The second professional is that the silencer is easy and simple to make use of. I do know lots of you need an ASIC due to the simplicity of use so you’ll undoubtedly admire that the Miner Silencer Field doesn’t add any further headache to the method.
The Silencer comes with a 4 digit temperature show that can assist you monitor the well being of your rig. On prime of that, it has a temperature alarm that rings if the miner floor exceeds 60°C, in addition to an influence lower characteristic in case the temperature goes increased than that and the rig is at risk.
Be aware: The ASIC / FPGA Silencer doesn’t supply sufficient cooling for units with an influence consumption increased than 1300W.
The facility consumption of the field is fairly low and it gained’t add an excessive amount of to the month-to-month value of the miner. We’re speaking about 36W with the followers off (solely the temperature monitoring circuits and show) and 120W with the followers on.
Miner Silencer Field Specs
| Enter | 110-240V AC |
|---|---|
| Present | 10A |
| Energy | Cooler Mode: 120W, Regular Mode: 36W |
| Cooler Temperature | 12°C |
| Working Temperature | -20°C – 50°C |
| Temperature Sensor | -25°C-150°C miner floor |
| Show | 4 digit temperature show |
| Excessive temperature alarm | Sure (60°C) miner floor |
| Community | RJ45 bridge |
| Dimensions | 88x36x41 cm |
| Weight | 10 kg |
| Compatibility | Blackminer F1, F1+, Extremely Imperium V1, V2 Antminer S9, S9i, S9j, L3+, X3, B3, A3, D3, V9, T9+, Z9-Mini, DR3 Baikal Big B, Big X10, Big N DragonMint B29, B52, X1, X2, T1 Avalon 821, 841, 851, 911, 920, 921 Innosilicon A5, A4+, A9, D9, D9+, S11, A9 ZMaster, T2, T3 Ebit E9 Whatsminer M3 Pinidea RR-200, DR-100, DR-100 PRO, DRX-Varyag, DRX-Kuznetsov, DR3 GMO miner B2, B3 Fusion Silicon X1, X6, X7and extra.. |
Getting Your Palms on One
In order for you a kind of unhealthy boys in your house/workplace you may test one of many hyperlinks beneath. Be part of the waitlist to be notified when the miner silencer field is obtainable for order.
Please share this text, extra orders = higher worth. Full overview coming quickly!
Have you ever tried a silencer field earlier than? Let me know within the feedback.
Obtained any query?
Thanks for studying. As at all times, your feedback, strategies and questions are welcome.
Subscribe and keep tuned for additional updates!
